🫠Intro to Engineering Unit 6 – Electrical & Electronic Engineering Basics

Key Concepts and Terminology

• Voltage (V) represents the potential difference between two points in an electrical circuit and is measured in volts
• Current (I) refers to the flow of electric charge through a conductor and is measured in amperes (A)
• Resistance (R) opposes the flow of electric current and is measured in ohms (Ω)
  • Conductors (copper, aluminum) have low resistance and allow current to flow easily
  • Insulators (rubber, plastic) have high resistance and prevent current from flowing
• Power (P) is the rate at which electrical energy is converted into other forms of energy (heat, light, motion) and is measured in watts (W)
• Ohm's Law establishes the relationship between voltage, current, and resistance in a circuit: $V = IR$
• Series circuits have components connected end-to-end, forming a single path for current flow
• Parallel circuits have components connected across the same two points, forming multiple paths for current flow

Fundamental Laws of Electricity

• Ohm's Law states that the current through a conductor is directly proportional to the voltage across it and inversely proportional to its resistance: $I = \frac{V}{R}$
• Kirchhoff's Current Law (KCL) states that the sum of currents entering a node equals the sum of currents leaving the node
  • A node is a point where two or more circuit elements connect
• Kirchhoff's Voltage Law (KVL) states that the sum of all voltages around a closed loop in a circuit equals zero
  • A closed loop is any path that starts and ends at the same point
• Faraday's Law of Induction describes how a changing magnetic field induces an electromotive force (EMF) in a conductor
• Lenz's Law states that the induced EMF in a conductor opposes the change in magnetic flux that produced it
• Coulomb's Law describes the force between two electrically charged particles: $F = k \frac{q_1 q_2}{r^2}$, where $k$ is Coulomb's constant, $q_1$ and $q_2$ are the charges, and $r$ is the distance between them
• Ampère's Circuital Law relates the magnetic field around a closed loop to the electric current passing through the loop

Circuit Components and Their Functions

• Resistors limit the flow of current in a circuit and are used for voltage division, current control, and heat generation
• Capacitors store electrical energy in an electric field and are used for filtering, timing, and smoothing voltage fluctuations
  • Capacitance (C) is measured in farads (F) and represents the ability of a capacitor to store charge
• Inductors store electrical energy in a magnetic field and are used for filtering, energy storage, and voltage regulation
  • Inductance (L) is measured in henries (H) and represents the ability of an inductor to store energy in a magnetic field
• Transformers convert AC voltage and current levels by using electromagnetic induction between two or more coils
• Diodes allow current to flow in only one direction and are used for rectification (AC to DC conversion) and voltage regulation
• Transistors amplify or switch electronic signals and are the building blocks of modern electronics (amplifiers, logic gates)
• Switches control the flow of current in a circuit by opening or closing contacts
• Fuses and circuit breakers protect circuits from excessive current by interrupting the current flow when it exceeds a predetermined level

Basic Circuit Analysis Techniques

• Equivalent resistance calculation simplifies series and parallel resistor combinations into a single equivalent resistance
  • For series resistors: $R_{eq} = R_1 + R_2 + ... + R_n$
  • For parallel resistors: $\frac{1}{R_{eq}} = \frac{1}{R_1} + \frac{1}{R_2} + ... + \frac{1}{R_n}$
• Voltage division determines the voltage across individual components in a series circuit using the voltage divider formula: $V_{out} = V_{in} \frac{R_2}{R_1 + R_2}$
• Current division determines the current through individual branches in a parallel circuit using the current divider formula: $I_1 = I_{total} \frac{R_2}{R_1 + R_2}$
• Mesh analysis applies KVL to solve for currents in a circuit by assigning a mesh current to each independent loop
• Nodal analysis applies KCL to solve for voltages in a circuit by assigning a reference node and writing equations for each remaining node
• Superposition theorem allows the analysis of a linear circuit with multiple sources by considering the effect of each source independently and then summing the results
• Thévenin's and Norton's theorems simplify complex circuits by replacing them with equivalent voltage or current sources and a single resistor

Power and Energy in Electrical Systems

• Electrical power is the rate at which electrical energy is converted into other forms of energy (heat, light, motion)
  • Instantaneous power: $P = VI$
  • For resistive loads: $P = I^2R = \frac{V^2}{R}$
• Electrical energy is the total amount of work done by an electrical system over time and is measured in joules (J) or watt-hours (Wh)
  • Energy: $W = Pt$, where $t$ is time
• Power factor (PF) is the ratio of real power to apparent power in AC circuits and ranges from 0 to 1
  • Real power (P) is the actual power consumed by the load and is measured in watts (W)
  • Reactive power (Q) is the power stored and released by inductors and capacitors and is measured in volt-ampere reactive (VAR)
  • Apparent power (S) is the total power supplied to the load and is measured in volt-amperes (VA)
• Three-phase power systems are used for efficient power transmission and distribution in industrial and commercial settings
  • Three-phase power consists of three sinusoidal voltages and currents with a phase difference of 120° between each phase
• Power quality issues (voltage sags, swells, harmonics) can affect the performance and lifespan of electrical equipment

Introduction to Electronic Devices

• Semiconductors (silicon, germanium) have electrical properties between those of conductors and insulators and are the basis for modern electronic devices
  • N-type semiconductors are doped with impurities that provide extra electrons (phosphorus, arsenic)
  • P-type semiconductors are doped with impurities that create electron holes (boron, gallium)
• PN junctions are formed when P-type and N-type semiconductors are combined, creating a diode that allows current to flow in only one direction
• Bipolar junction transistors (BJTs) have three regions (emitter, base, collector) and are used for amplification and switching
  • NPN transistors have a thin P-type base between two N-type regions
  • PNP transistors have a thin N-type base between two P-type regions
• Field-effect transistors (FETs) use an electric field to control the conductivity of a channel between the source and drain terminals
  • Junction FETs (JFETs) have a reverse-biased PN junction to control the channel
  • Metal-oxide-semiconductor FETs (MOSFETs) use a voltage applied to an insulated gate to control the channel
• Operational amplifiers (op-amps) are high-gain differential amplifiers used for signal conditioning, filtering, and mathematical operations
• Digital logic gates (AND, OR, NOT, NAND, NOR, XOR) perform Boolean operations on binary inputs and are the building blocks of digital circuits

Practical Applications and Examples

• Power supply circuits convert AC to DC (rectifiers), regulate voltage (voltage regulators), and filter ripple (capacitors)
  • Half-wave rectifiers use a single diode to convert AC to pulsating DC
  • Full-wave rectifiers use multiple diodes or a center-tapped transformer to convert AC to DC with less ripple
• Amplifier circuits increase the amplitude of small signals for audio (speakers, microphones), radio (antennas), and instrumentation (sensors)
  • Class A amplifiers have a single transistor that conducts for the entire input cycle, providing low distortion but low efficiency
  • Class B amplifiers have two transistors that each conduct for half of the input cycle, providing higher efficiency but more distortion
  • Class AB amplifiers combine the benefits of Class A and Class B by allowing a small amount of overlap in transistor conduction
• Filter circuits remove unwanted frequencies from a signal, such as low-pass filters (remove high frequencies), high-pass filters (remove low frequencies), and band-pass filters (allow a specific range of frequencies)
• Oscillator circuits generate periodic signals (sine, square, triangle waves) for timing, clocks, and carrier signals
  • RC oscillators use resistors and capacitors to generate low-frequency signals
  • LC oscillators use inductors and capacitors to generate high-frequency signals
  • Crystal oscillators use the piezoelectric effect of quartz crystals for high stability and accuracy
• Motor control circuits regulate the speed, torque, and direction of electric motors using power electronic devices (MOSFETs, IGBTs)
  • H-bridge circuits allow bidirectional control of DC motors
  • Variable frequency drives (VFDs) control the speed of AC motors by adjusting the frequency and voltage of the power supply

Common Challenges and Troubleshooting

• Open circuits occur when there is a break in the current path, preventing current from flowing
  • Causes: broken wires, loose connections, damaged components
  • Symptoms: no current flow, infinite resistance, no voltage drop across the open component
• Short circuits happen when two points of different potential are connected with low resistance, causing excessive current flow
  • Causes: damaged insulation, incorrect wiring, component failure
  • Symptoms: high current flow, low resistance, blown fuses or tripped circuit breakers
• Grounding issues can cause safety hazards, signal interference, and equipment damage
  • Proper grounding provides a low-resistance path for fault currents and helps to stabilize voltage references
  • Ground loops occur when there are multiple paths to ground, causing circulating currents and noise
• Electromagnetic interference (EMI) can disrupt the operation of electronic devices by inducing unwanted signals
  • Sources: power lines, motors, switching power supplies, radio transmitters
  • Prevention: shielding, grounding, filtering, proper circuit layout and wiring practices
• Component tolerance and aging can cause circuits to drift from their designed performance over time
  • Resistors, capacitors, and inductors have manufacturing tolerances that affect their actual values
  • Electrolytic capacitors and batteries can degrade with age and use, causing changes in circuit behavior
• Debugging techniques for electronic circuits include visual inspection, continuity testing, voltage and current measurements, and signal tracing
  • Divide and conquer approach: isolate sections of the circuit to narrow down the problem area
  • Compare measurements to expected values based on circuit analysis and design specifications
  • Use oscilloscopes to visualize time-varying signals and identify issues such as noise, distortion, and timing errors