🔦Electrical Circuits and Systems II Unit 4 – Resonance and Q Factor in Circuits

Key Concepts

• Resonance occurs when the inductive and capacitive reactances in a circuit are equal and cancel each other out
• At resonance, the impedance of the circuit is purely resistive and reaches its maximum value
• The frequency at which resonance occurs is called the resonant frequency, denoted as $f_r$ or $\omega_r$
• Q factor is a dimensionless parameter that describes the sharpness of the resonance peak and the energy storage efficiency of the circuit
• Higher Q factor indicates a narrower bandwidth, greater frequency selectivity, and lower energy dissipation
• Bandwidth is the range of frequencies over which the circuit's response is within a specified limit (typically -3dB) of its maximum value
• Series and parallel RLC circuits exhibit different characteristics at resonance, such as maximum current (series) or maximum voltage (parallel)
• Resonant circuits find applications in various electrical systems, including filters, oscillators, and communication systems

Resonance Fundamentals

• Resonance is a phenomenon that occurs in circuits containing inductors (L) and capacitors (C) when the inductive and capacitive reactances are equal in magnitude
• At resonance, the impedance of the circuit is purely resistive, as the inductive and capacitive reactances cancel each other out
• The resonant frequency $f_r$ is given by the formula: $f_r = \frac{1}{2\pi\sqrt{LC}}$
  • Alternatively, the angular resonant frequency $\omega_r$ is given by: $\omega_r = \frac{1}{\sqrt{LC}}$
• The impedance of the circuit at resonance is equal to the resistance (R) and reaches its maximum value
• The phase angle between the voltage and current at resonance is zero, indicating that the circuit is purely resistive
• The current and voltage in the circuit are in phase with each other at resonance
• The energy stored in the inductor and capacitor oscillates between them, with the maximum energy stored in one component when the other has zero energy

Series RLC Circuits

• In a series RLC circuit, the resistor (R), inductor (L), and capacitor (C) are connected in series
• The total impedance of a series RLC circuit is given by: $Z = R + j(\omega L - \frac{1}{\omega C})$
• At the resonant frequency, the inductive and capacitive reactances are equal and cancel each other out, resulting in a purely resistive impedance
• The current in a series RLC circuit reaches its maximum value at resonance, as the impedance is at its minimum (equal to R)
• The voltage across the inductor and capacitor at resonance are equal in magnitude but opposite in phase, resulting in a net voltage of zero across the LC combination
• The quality factor (Q) of a series RLC circuit is given by: $Q = \frac{\omega_r L}{R} = \frac{1}{\omega_r CR}$
• A higher Q factor in a series RLC circuit results in a narrower bandwidth and greater frequency selectivity

Parallel RLC Circuits

• In a parallel RLC circuit, the resistor (R), inductor (L), and capacitor (C) are connected in parallel
• The total admittance of a parallel RLC circuit is given by: $Y = \frac{1}{R} + j(\omega C - \frac{1}{\omega L})$
• At the resonant frequency, the inductive and capacitive susceptances are equal and cancel each other out, resulting in a purely conductive admittance
• The voltage across a parallel RLC circuit reaches its maximum value at resonance, as the impedance is at its maximum (equal to R)
• The currents through the inductor and capacitor at resonance are equal in magnitude but opposite in phase, resulting in a net current of zero through the LC combination
• The quality factor (Q) of a parallel RLC circuit is given by: $Q = \frac{R}{\omega_r L} = \omega_r RC$
• A higher Q factor in a parallel RLC circuit results in a narrower bandwidth and greater frequency selectivity

Q Factor Explained

• The quality factor, or Q factor, is a dimensionless parameter that describes the sharpness of the resonance peak and the energy storage efficiency of a resonant circuit
• Q factor is defined as the ratio of the energy stored in the circuit to the energy dissipated per cycle at resonance
• Mathematically, Q factor is expressed as: $Q = \frac{\omega_r L}{R} = \frac{1}{\omega_r CR}$ for series RLC circuits, and $Q = \frac{R}{\omega_r L} = \omega_r RC$ for parallel RLC circuits
• A higher Q factor indicates a narrower bandwidth, greater frequency selectivity, and lower energy dissipation
  • Circuits with high Q factors are more sensitive to changes in frequency and have a sharper resonance peak
• The bandwidth of a resonant circuit is inversely proportional to its Q factor, given by: $BW = \frac{f_r}{Q}$
• Q factor is affected by the resistance in the circuit, with lower resistance resulting in a higher Q factor
• In practical applications, the Q factor is limited by the inherent resistances of the components and the circuit's design constraints

Bandwidth and Selectivity

• Bandwidth is the range of frequencies over which the circuit's response is within a specified limit (typically -3dB) of its maximum value
• The -3dB bandwidth is the frequency range between the points where the circuit's response falls to 70.7% of its maximum value
• Bandwidth is inversely proportional to the Q factor of the circuit, given by: $BW = \frac{f_r}{Q}$
  • A higher Q factor results in a narrower bandwidth, while a lower Q factor results in a wider bandwidth
• Selectivity is the ability of a circuit to respond to a specific frequency while rejecting others
• Resonant circuits with high Q factors have greater frequency selectivity, as they respond strongly to frequencies near the resonant frequency and attenuate frequencies further away
• The shape of the resonance curve (plot of circuit response vs. frequency) indicates the selectivity of the circuit
  • A narrow, sharp peak indicates high selectivity, while a broad, flat peak indicates low selectivity
• In filter applications, the bandwidth and selectivity of the resonant circuit determine its ability to pass or reject specific frequency components of a signal

Applications in Electrical Systems

• Resonant circuits find numerous applications in various electrical systems, leveraging their unique properties at resonance
• Filters: Resonant circuits are used to design filters that pass or reject specific frequency components of a signal
  • Band-pass filters: Allow a specific range of frequencies to pass while attenuating others
  • Band-stop filters: Reject a specific range of frequencies while allowing others to pass
• Oscillators: Resonant circuits are used in oscillator designs to generate sinusoidal signals at a specific frequency
  • The resonant frequency of the circuit determines the oscillation frequency
  • Examples include LC oscillators and crystal oscillators
• Tuned amplifiers: Resonant circuits are used in amplifier stages to provide frequency-selective amplification
  • The resonant circuit is tuned to the desired frequency, providing maximum gain at that frequency while attenuating others
• Impedance matching: Resonant circuits can be used for impedance matching between different stages of a system
  • By tuning the circuit to the desired frequency, maximum power transfer can be achieved
• Wireless communication: Resonant circuits are used in antennas and RF circuits for wireless communication systems
  • The resonant frequency of the antenna determines its operating frequency and bandwidth
• Power systems: Resonant circuits are used in power factor correction and harmonic filtering applications
  • Tuned filters can be used to eliminate specific harmonic frequencies from the power system

Problem-Solving Techniques

• When solving problems related to resonant circuits, it is essential to identify the type of circuit (series or parallel) and the given parameters
• Determine the resonant frequency using the appropriate formula: $f_r = \frac{1}{2\pi\sqrt{LC}}$ or $\omega_r = \frac{1}{\sqrt{LC}}$
• Calculate the impedance of the circuit at resonance, which is equal to the resistance (R) for both series and parallel circuits
• Use the Q factor formulas to determine the quality factor of the circuit: $Q = \frac{\omega_r L}{R} = \frac{1}{\omega_r CR}$ for series, and $Q = \frac{R}{\omega_r L} = \omega_r RC$ for parallel
• Calculate the bandwidth of the circuit using the formula: $BW = \frac{f_r}{Q}$
• When dealing with complex impedances, use phasor notation and complex algebra to simplify the expressions
• Apply Kirchhoff's voltage law (KVL) and Kirchhoff's current law (KCL) to analyze the voltages and currents in the circuit
• Use the voltage divider rule and current divider rule to determine the voltages and currents across individual components
• When solving for unknown values, rearrange the equations to isolate the desired variable and substitute the given values
• Verify the results by checking the units and ensuring they make sense in the context of the problem